ss-redir − shadowsocks client as transparent proxy, libev port
ss−redir [−AuUv] [−h|−−help] [−s <server_host>] [−p <server_port>] [−l <local_port>] [−k <password>] [−m <encrypt_method>] [−f <pid_file>] [−t <timeout>] [−c <config_file>] [−b <local_address>] [−a <user_name>] [−n <nofile>]
Shadowsocks−libev is a lightweight and secure socks5 proxy. It is a port of the original shadowsocks created by clowwindy. Shadowsocks−libev is written in pure C and takes advantage of libev to achieve both high performance and low resource consumption.
Shadowsocks−libev consists of five components. ss−redir(1) works as a transparent proxy on local machines to proxy TCP traffic and requires netfilter’s NAT module. For more information, check out shadowsocks−libev(8) and the following EXAMPLE section.
−s <server_host>
Set the server’s hostname or IP.
−p <server_port>
Set the server’s port number.
−l <local_port>
Set the local port number.
−k <password>
Set the password. The server and the client should use the same password.
−m <encrypt_method>
Set the cipher.
Shadowsocks−libev accepts 18 different ciphers:
table, rc4, rc4−md5, aes−128−cfb, aes−192−cfb, aes−256−cfb, bf−cfb, camellia−128−cfb, camellia−192−cfb, camellia−256−cfb, cast5−cfb, des−cfb, idea−cfb, rc2−cfb, seed−cfb, salsa20, chacha20 and chacha20−ietf.
The default cipher is table.
If built with PolarSSL or custom OpenSSL libraries, some of these ciphers may not work.
−a <user_name>
Run as a specific user.
−f <pid_file>
Start shadowsocks as a daemon with specific pid file.
−t <timeout>
Set the socket timeout in seconds. The default value is 60.
−c <config_file>
Use a configuration file.
Refer to shadowsocks−libev(8) CONFIG FILE section for more details.
−n <number>
Specify max number of open files.
Only available on Linux.
−b <local_address>
Specify local address to bind.
−u
Enable UDP relay.
TPROXY is required in redir mode. You may need root permission.
−U
Enable UDP relay and disable TCP relay.
−A
Enable onetime authentication.
−v
Enable verbose mode.
−h|−−help
Print help message.
ss−redir requires netfilter’s NAT function. Here is an example:
# Create new
chain
root@Wrt:~# iptables −t nat −N SHADOWSOCKS
# Ignore your
shadowsocks server's addresses
# It's very IMPORTANT, just be careful.
root@Wrt:~# iptables −t nat −A SHADOWSOCKS
−d 123.123.123.123 −j RETURN
# Ignore LANs
and any other addresses you'd like to bypass the proxy
# See Wikipedia and RFC5735 for full list of reserved
networks.
# See ashi009/bestroutetb for a highly optimized CHN route
list.
root@Wrt:~# iptables −t nat −A SHADOWSOCKS
−d 0.0.0.0/8 −j RETURN
root@Wrt:~# iptables −t nat −A SHADOWSOCKS
−d 10.0.0.0/8 −j RETURN
root@Wrt:~# iptables −t nat −A SHADOWSOCKS
−d 127.0.0.0/8 −j RETURN
root@Wrt:~# iptables −t nat −A SHADOWSOCKS
−d 169.254.0.0/16 −j RETURN
root@Wrt:~# iptables −t nat −A SHADOWSOCKS
−d 172.16.0.0/12 −j RETURN
root@Wrt:~# iptables −t nat −A SHADOWSOCKS
−d 192.168.0.0/16 −j RETURN
root@Wrt:~# iptables −t nat −A SHADOWSOCKS
−d 224.0.0.0/4 −j RETURN
root@Wrt:~# iptables −t nat −A SHADOWSOCKS
−d 240.0.0.0/4 −j RETURN
# Anything else
should be redirected to shadowsocks's local port
root@Wrt:~# iptables −t nat −A SHADOWSOCKS
−p tcp −j REDIRECT −−to−ports
12345
# Add any UDP
rules
root@Wrt:~# ip rule add fwmark 0x01/0x01 table 100
root@Wrt:~# ip route add local 0.0.0.0/0 dev lo table 100
root@Wrt:~# iptables −t mangle −A SHADOWSOCKS
−p udp −−dport 53 −j TPROXY
−−on−port 12345
−−tproxy−mark 0x01/0x01
# Apply the
rules
root@Wrt:~# iptables −t nat −A PREROUTING
−p tcp −j SHADOWSOCKS
root@Wrt:~# iptables −t mangle −A PREROUTING
−j SHADOWSOCKS
# Start the
shadowsocks−redir
root@Wrt:~# ss−redir −u −c
/etc/config/shadowsocks.json −f
/var/run/shadowsocks.pid
ss−local(1), ss−server(1), ss−tunnel(1), ss−manager(1), shadowsocks−libev(8), iptables(8), /etc/shadowsocks−libev/config.json